Honeywell iaq owners manual

This will temporarily over- ride the temperature setting for the cur- rent time period. This will turn off the program schedule. Whatever temperature you set will be Inside Set To maintained 24 hours a day, until you Page Vacation Hold Operating Manual Vacation hold 1 Set temperature This feature can suspend the program schedule for extended periods of time.

The screen will remain locked for 30 seconds so you can clean the screen without changing any settings. Page Optional Remote Sensors Operating Manual Optional remote sensors If an outdoor sensor is installed, the cur- rent outdoor temperature is displayed.

Thermostat is non-programmable. Options: Program schedule is on 7-day programmable. Page 26 Operating Manual Advanced functions Furnace filter change reminder Function This feature displays an alert to remind you to change the fur- nace filter.

Most problems can be corrected quickly and easily. Make sure the temperature is set cooling system higher than the Inside temperature. Page Limited Warranty , or whether a replacement product can be sent to you.

This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Honeywell that the defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer.

Page 32 Printed in U. All rights reserved. Choix : La programmation est en marche 7 jours programmable. Fonction Horloge 12 heures c.

D; H; H et autres brevets en instance. Page Sensores Remotos Opcionales Manual de Uso Sensores remotos opcionales Si hay un sensor exterior instalado, se muestra la temperatura exterior actual. El termostato no es programable. Page 96 Printed in U. Print page 1 Print document 96 pages. Rename the bookmark. Delete bookmark? Cancel Delete. See page 2 to check settings. Your new thermostat is pre-programmed and ready to go.

Just set the time and day. Then check the settings below and change if needed:. Set clock. Select fan setting: Preset to Auto Select system setting: Preset to Heat Inside humidity If an outdoor sensor is installed, the outdoor temperature is shown. Press MORE to display the humidity level. Note: To change the current week day display, see page Use this setting for improved air circulation, or for more efficient air cleaning, if you do not want the fan to run all the time.

If you select On or Circ , the setting you select will remain active until you press FAN again to select Auto , and return to the fan schedule. You can program four time periods each day, with different settings for each day. Note: Press FAN to customize fan settings for any time period see page 6. This will temporarily override the temperature setting for the current time period.

The new temperature will be maintained only until the time you set. The program schedule will resume. Inside 70 Set To Press HOLD to permanently adjust the temperature. This will turn off the program schedule. Whatever temperature you set will be maintained 24 hours a day for the number of days you select. After this number of days have elapsed, the previously programmed schedule will resume at the time you set. Auto Changeover: When set to Auto , the thermostat automatically selects heating or cooling depending on the indoor temperature.

Compressor Protection: This feature forces the compressor to wait a few minutes before restarting, to prevent equipment damage.

Flashing message: Reminder to replace filter or UV lamp. Southern Away Dehumidification: Your system may be programmed to control humidity while your house is vacant during the humid season. Before you leave the house, press the HOLD button three times to activate this feature. This will control temperature and humidity to help protect your house and possessions while you are away. If this feature does not work, contact your installer.

When the screen is fully locked, no keys function. To lock or unlock the screen, see advanced function on page The screen will remain locked for 30 seconds so you can clean the screen without changing any settings. Note: Do not spray any liquid directly on the thermostat. Spray liquids onto a cloth, then use the damp cloth to clean the screen. Use water or household glass cleaner. Avoid abrasive cleansers. If an outdoor sensor is installed, the current outdoor temperature is displayed.

If an indoor remote sensor is installed, the display shows the indoor temperature at the location of the sensor. If more than one indoor sensor is installed, the display shows an average of temperature readings from all sensors or an average between the thermostat and the sensor s. Wait at least 1 day before adjusting the frost level again. Once frost no longer appears, the thermostat will control humidity to the maximum level without frosting or fogging windows and without further adjustment.

Note: If you do not have an outdoor temperature sensor, the Frost Control level will not be displayed. AUTO If installed to control a dehumidifier, the thermostat can activate it as needed to reduce humidity. You can set the timer to ventilate from 20 to minutes, in minute increments. To turn off the ventilator, select 0. If programmed for auto-ventilation by the installer, the thermostat will ventilate your home as needed.

Ventilation can still be requested by using the timer when set to Off. The thermostat is pre-programmed to automatically adjust to daylight savings time. If you have difficulty with your thermostat, please try the following suggestions. See Advanced function on page 22 for backlight options. Welcome to ManualMachine. We have sent a verification link to to complete your registration.