Vizio model e601i a3 manual

Regards, Shelagh. I replaced the t con board with one I bought from shopjimmy and I still get no picture. Screen lights up but no picture.

Hi Adam, Did you check the lamp and reset the lamp timer. You usually have to replace the lamp after changing the t-con board. They can help you solve this problem. Wish the removal of the back panel were as easy as you state. After all screws are removed you still have interlocks on both sides to deal with. Hi HB, We will update our manual. Some of the new models do those side interlocks. Thanks for pointing out that omission. I was getting very dim picture so I replaced all three boards inside but now the picture is worse it has lines in it now..

Anyone have any input? Hi Whiteywood, If you were getting white vertical lines then the main board needs to be replaced. Sounds like you have done this. Did you check the ribbon connectors so they were properly cleaned and connected? If may also be the T-Con that needs to be replaced. That is a different element from the main board. Is the TV still under warranty? Do not install your TV close to smoke. Operating your TV close to smoke or moisture may cause fire or electric shock. To ensure reliable operation of your TV and to protect it from overheating, be sure these openings are not blocked or covered.

Do not place your TV in a bookcase or cabinet unless proper ventilation is provided. Do not place any objects on the top of your TV. Doing so could short circuit parts causing a fire or electric shock.

Never spill liquids on your TV. If you are not sure of the type of power supplied to your home, consult your dealer. This may compromise the integrity of the display. For more information, contact your dealer. To totally disconnect power, unplug the power cord.

Overloading can result in fire or electric shock. Any other voltage than the specified voltage may cause fire or electric shock.

To avoid electric shock, avoid handling the power cord during electrical storms. This will protect your TV from damage due to power surges. Opening or removing the back cover may expose you to high voltages, electric shock, and other hazards. If repair is required, contact your dealer and refer all servicing to qualified service personnel. Do not expose your TV to rain or moisture. If water penetrates into.

Continuous use in this case may result in fire or electric shock. If any smoke or odor becomes apparent, unplug the power cord and contact your dealer immediately. Do not try to repair your TV yourself. If your TV is dropped and the housing is damaged, the internal. Unplug the power cord immediately and contact your dealer for repair. Continued use of your TV may cause fire or electric shock.

Operating your TV in environments with heavy dust or high humidity may cause fire or electric shock. Ensure that the power cord and any other cables are unplugged before moving your TV. Pulling on the power cord may damage the wires inside the cord and cause fire or electric shock. When your TV will not be used for an extended period of time, unplug the power cord.

Incorrect polarities may cause the batteries to leak which can damage the remote control or injure the operator. Do not expose batteries to excessive heat such as sunshine, fire or the like. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

For added protection of the TV during a lightning storm or when it is left unattended or unused for long periods of time, unplug the TV from the wall outlet and disconnect the antenna or cable system. Do not locate the antenna near overhead light or power circuits, or where it could fall into such power lines or circuits.

Remember, the screen of the coaxial cable is intended to be connected to earth in the building installation. Antenna Lead In Wire. NEC Section Installing the TV Back Panel Side Panel Front Panel Remote Control Setting Timers Before installing your new TV, take a moment to inspect the package contents.

Use the images below to ensure nothing is missing or damaged. After removing the TV from the box and inspecting the package contents you can begin installing the TV. Your TV can be installed in two ways:. Your TV includes a stand designed to support the weight of the TV and keep it from falling over. However, the TV can still fall over if:. It is recommended that two people take part in the base installation.

Place the TV screen-down on a clean, flat surface. To prevent scratches or damage to the screen, place the TV on a soft surface such as a blanket. Insert the three 3 M5 16mm included Phillips screws and tighten them using a Phillips screwdriver to secure the base to the TV. When you are finished, place the TV on a stable, level surface. To mount your TV on a wall, you will need a wall mount.

Consult the information below to find the appropriate mount for your TV model:. Installing a TV on a wall requires lifting. To prevent injury or damage to the TV, ask someone to help you. Be sure the mount you choose is capable of supporting the weight of the TV. After you have determined that you have the correct mount for your TV, you can begin the installation. Disconnect any cables connected to your TV. Place the TV face-down on a clean, flat, stable surface.

Be sure the surface is clear of debris that can scratch or damage the TV. Remove the base by loosening and removing the screws. Attach your TV and wall mount to the wall, carefully following the instructions that came with your mount. See Appendix B - Specifications on page For some wall mounts, you may want to use cables with right-angle connectors.

This allows the TV to rest closer to the wall. The power indicator flashes on when the TV turns on, then goes out after several seconds. Use with number pad to manually enter a digital sub-channel. For example, or Press and hold while pressing another key to enter a blue character. For example, press ALT and W to enter a character. Insert two batteries into the remote control. Turn the TV and your device off.

Connect the appropriate cable not included to the TV and the device. Turn the TV and your device on. Component cables are designed to carry high definition video signals along with additional audio connections. Colors are delivered with color information split up three different ways over three connectors for video separated into Red, Blue and Green signals and the left and right audio connectors Red and White.

HDMI is the intelligent, all-digital interface that delivers both dazzling quality and unmatched ease of use. HDMI technology transmits crystal-clear digital video along with multi-channel surround audio. HDMI-connected devices have the ability to automatically adjust themselves for optimal viewing.

This cable transmits video. Connect a 3. This cable transmits audio. See Appendix B - Specifications. Turn the TV and your audio device off. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password.

Product Registration To purchase or inquire about accessories and installation services for your VIZIO product, visit our website at www. When Reading this Manual When you see this symbol, please read the accompanying important warning or notice.

When you see this symbol, please read the accompanying helpful tip. Important Safety Instructions Your TV is designed and manufactured to operate within defined design limits. If your TV is dropped and the housing is damaged, the internal components may function abnormally.

Lightning Protection For added protection of the TV during a lightning storm or when it is left unattended or unused for long periods of time, unplug the TV from the wall outlet and disconnect the antenna or cable system. Power Lines Do not locate the antenna near overhead light or power circuits, or where it could fall into such power lines or circuits. Ground Clamp Electric Service Equipment. Table of Contents Installing the TV Changing the Screen Aspect Ratio Setting Up Closed Captioning Plus App Dock Using the Hot Keys Plus Apps Window Plus Apps Window Overview Installing the TV 1.

Inspecting the Package Contents Before installing your new TV, take a moment to inspect the package contents. To install the base: 1. Remove any plastic wrapping from the TV and the stand. Consult the information below to find the appropriate mount for your TV model: Installing a TV on a wall requires lifting.

To install your TV on a wall: 1. Ethernet - Connect an Ethernet cable from a home network. Coaxial - Connect a coaxial cable from a cable or satellite box, or an antenna. PC Audio In - Connect a 3. Back Panel. MENU - Open the on-screen menu. Side Panel. Front Panel. Input Change the currently-displayed input. Closed Captions Open the closed caption menu.

Exit Close the on-screen menu.